Stiffen Your Hat With Wax

Standard

There is nothing worse than a floppy cowboy hat. Steaming a cowboy hat will stiffen it for a short time, but just a short time. What I want is to steam my cowboy hats, shape them and never have to do it again, but when you spend $35 for a hat or buy one at Bi-Mart for $19.99 you can count on re-steaming on a regular basis to bring back the stiffness. I’ve tried spray starch and some formula that I got off the internet which included corn starch, but nothing really works for long and I’m back to steaming and shaping my hats again.

When I was a kid my brothers and I wore cowboy hats. Usually they were hand-me-downs from my dad or what he’d picked up at a second hand store. And usually they were too big and out of shape when we got them. To adjust for the too big size, my dad would roll up a sheet of newspaper and tuck it in behind the sweat band, adding more or less paper until it fit our tiny heads. One time, my mom sewed the crown together so the hat wouldn’t slip down over my ears.

My dad would always steam them and shape our new/used hats to our desired style and to stiffen them again, but kids are tough on hats and we would be begging him to re-steam them again for us. He too got tired of steaming and shaping hats, so using his vast ingenuity, he decided to wax our hats. I can still remember him melting the wax on the stove and painting it onto my white cow hat. When the wax cooled it was stiff as a board and as waterproof a ducks’ back! I also remember that it looked like it had a layer of wax on it, but that was okay because it was a white hat and the wax is white.

I have a brown cowboy hat that I wear around the farm when it’s cold and rainy. It keeps my head warm and the rain off my spectacles. But it does get beat up and out of shape fairly quickly. I don’t really care how it looks as long as it works, but I do reshape it occasionally. I also have a black cowboy hat that I wear at work when it’s cold and raining. It gets tossed around in the truck and before long it needs to be re-stiffened, re-shaped and occasionally, waterproofed. In the back of my mind, I kept remembering my dad waxing my hat and how nice and stiff it was, so I decided to give it a try.

The first thing I needed was some paraffin wax. You would think it would be easy enough to buy paraffin wax, but unless it’s canning season, it can be hard to come by. I finally settled on a white, unscented candle. I chose unscented because scented candles put out too much soot when they burn, and I didn’t want my hats to smell like a flower.20160228_172120

I thought I’d melt the candle with the old griddle that I have in my shop for heating things, but that was too slow, so I fired up my Harbor Freight heat gun, which melted the candle much faster. With the wax melted, I used a small paint brush to paint the wax onto the underside of the brim and the inside of the crown. I painted the inside and underside because if there was a waxy residue, it would be less noticeable on the inside/underside.20160228_172259 There was a waxy residue when I got done, because the felt didn’t absorb much of the wax. Now this is where my dad stopped, he just painted the hot wax on and let the hat felt absorb as much as it would, which is fine on a kid’s white hat, because who cares how a kids hat looks, right? Well, as I mentioned, my hats are brown and black and I’m not a kid. So, to get the wax to melt into the felt I used my heat gun and heated the wax on the hat. To my delight and surprise, the wax melted and was absorbed into the felt almost completely. What didn’t absorb, I brushed with a stiff bristle brush, removing what wax I could, and then heated the wax again until it was all absorbed into the hat.20160228_172821

When the hat cooled, it was stiff and waterproof. The process worked so well that I also waxed my black hat. I’ve been wearing my hats for about a week now and I am very pleased. I may have put a little too much wax on the inside of the crown of the black hat because there is a slight white waxy residue. However, no one but me knows it’s there and I don’t care.20160228_172918 Would I recommend that you wax your $200 Stetson? No! But if you have an old hat that just won’t hold its form anymore and you are going to toss it, give waxing a try and it just might become your favorite kick-around- in- hat.

Anyway…for what it’s worth.

Advertisements

MAKING ROOM FOR THE WIFE

Standard

DSCF7322

When my wife committed to joining me on our riding groups’ annual adventure to Baker City Oregon, I realized that our bike was not set up or rated to carry us and all the personal items that would be required to keep us in clean clothes and beautified for a week.

Our Suzuki Volusia 800cc has a Gross Vehicle Weight Rating, GVWR, of about 950 lbs. The bike alone weights 590lbs. This means that my wife and our luggage, tools and miscellaneous items would have to weight 90 lbs. My wife alone weighs close to 90lbs. (You’re welcome babe). I weigh…do the math. Well you get the idea, we would be way over the GVWR. We got out our “Motorcycle Trip Packing List” (see my blog, “Motorcycle Packing List”) and started crossing things off the list that we could live without. When all was said and done we got our stack of essentials to fit into two small pieces of luggage, airplane carry-on style, and our biggest motorcycle trunk. In the past, when I used the Volusia for a trip I would just strap a bag on the passenger seat, cram a bunch of stuff in the hard shell saddlebags and be off. The problem now was that our Volusia was not set up to carry two pieces of luggage, my wife, and I. My V-strom is setup for exactly that scenario, (see my blog, “Panniers Made From Scratch”) but the V-strom isn’t nearly as comfortable as the Volusia to ride, it has Corbin seats.

For the next couple of days I scratched my head and tried to figure out how I was going remove the hard shell saddlebags and replace them with two pieces of carry-on luggage. I finally concluded that I would have to make another set of plastic panniers for the Volusia, exactly like those I made for my V-strom. That’s right, I said “exactly” like those for the V-strom. The panniers for the V-strom attach to the bike using a metal frame work that I designed and made. The Volusia didn’t have that same frame work, but it did have the saddlebag supports and the mounting studs that attach the saddlebags to the bike. Retro-fitting the panniers to the Volusia was as easy as drilling two holes in the back of the plastic panniers so they would slip onto the studs and clip in place just like the saddlebags. To make them extra secure and for added support I added a couple of straps. Now granted, it didn’t look “Harley Cool,” but it worked great.

DSCF7382

Showing plastic panniers on Volusia with studs showing and extra straps for support.

DSCF7373

Showing luggage in place in plastic panniers and covered with bright rain proof bags.

I knew that once we got to Baker City we would be removing the plastic panniers and luggage, which presented two more issues. First, with them removed, the bike is left with two large and ugly, metal ell brackets sticking out on both sides of the bike where the bags mount.

DSCF7383

Showing ugly metal support brackets for saddlebags

And second, the trunk wouldn’t be large enough to pack all the stuff we would need for the long day trips we would be taking from Baker City. My first thought was to pack the saddlebags full of clothes and pack the packed saddlebags in the luggage, but they were too big and too heavy.

When I first started riding dual sport I wanted some small saddle bags I could attach to my Honda XR650L to carry essentials, like tools, rain gear, water and power bars. I didn’t want to spend a lot of money on brand named soft saddlebags, so I would stop by Goodwill every now and then to see if I could find pairs of backpacks, duffel bags or small soft sided luggage bags that were identical or very similar in size and appearance. Lucky enough, I was able to collect a few pairs of bags that looked alike or were exactly alike. I found two identical Goodwill bags in our motorcycle stall storage cabinet that would be a good size for day ride purposes. I could have just strapped them on the bike like saddlebags, but after modifying my plastic panniers the idea of making simple plastic supports that would attach just like the saddlebags and panniers seemed like the best plan.

I took one of the plastic barrels that I had and cut off two rectangles that were the same width as the small bags, 11.5”, and that were the same length in height + depth as the bags, 17”. Using a propane torch I heated and bent the plastic rectangles into two large ell shaped brackets. I drilled holes in the brackets to match the mounting studs on the bike so they too would slip onto the studs and clip in place.

Both bags had large open pockets on the back of them. I cut the pockets open along the bottom and reinforced the cut material with Gorilla Duct Tape, love the stuff. Next I slipped the bracket up through the open bottom of the pocket. The modified pocket held the bag to the bracket, the bag was supported by the bottom of the plastic ell and the bracket clipped easily to the motorcycle saddlebag studs.

DSCF7378

Showing plastic ell bracket and small bag.

DSCF7379

Showing ell bracket inserted through cut open back pocket.

DSCF7385

showing small bag mounted on the bike

The small bags were lightweight, could easily be packed with clothes and packed nicely into our luggage. They were large enough to carry what we needed for day trips and were even rain resistant. They did look a little redneck and defiantly not “Harley Cool”, but I’m not what you would call “cool.”

Anyway…for what it’s worth.

Getting All Decked Out

Standard

DSCF7226

About seven or eight years ago I bought a Big Tex utility trailer. We needed something to haul motorcycles, livestock, hay, firewood, lumber, well to haul stuff. After looking around for a month for a used trailer that I thought would be the right size and have a loading ramp/tailgate I decided, after asking my wife, to buy a new Big Tex trailer. I remember the salesperson telling me that wood deck was white pine and stated the fact as if it were a selling point. I didn’t want to burst his bubble, so I let the comment slide, but knew that I would have to replace the wood deck in a few years because in this area pine would decay quickly. Over the years and to try and extend the life of the wood deck, I cleaned it and sealed it with deck stain. I’m confident that my efforts helped extend the life of the wood, but ultimately the wood decayed. The first failure was when I was loading a Suzuki GS 850 onto the trailer, my second winter motorcycle project this year. (See my blog The Transformer). As we pushed it onto the trailer the back tire broke through one of the planks. And so it began. I patched the broken board with a piece of plywood and over the next four months of use the trailer deck became a patch work of pieces of plywood. The last straw was last weekend when my son-in-law, Dustin, was moving the trailer, by hand, out of the way so he could get to his camp trailer. At the time my Tex didn’t have the four foot metal tailgate/loading ramp on it and I knew the tongue would be heavy so I thought I’d help Dustin by stepping up on the back of the trailer to counterbalance the weight off the tongue. As I stepped up onto the trailer the wood deck broke through and I was standing on the ground.

Thursday evening he called me and asked if he could borrow my trailer to haul my mower up to my mountain property to mow so my daughter, his wife, will have a nicely cut meadow for her and her friends to camp on. Of course I said yes, knowing that I would have to replace the deck on the trailer before it would be safe to use again. Last night, Friday, after work I removed the most rotted boards so they wouldn’t fall out on the road and drove to Home Depot, trailer in tow, to buy some pressure treated lumber to replace the rotted deck. I could have replaced the deck with untreated Doug Fir and it would have lasted several years if I kept it clean and stained, but even if it lasted ten years I’d have to replace it again and I’d be…well old and I knew I wouldn’t want to mess with replacing the deck again. When you get to be my age you start to considering things like that. If I was thirty I would have used Doug Fir and saved $60.00, but at my age you do the math and knowing you won’t live forever and your health may not always be excellent, you make different decisions.

What is left of the original trailer decking.

What is left of the original trailer decking.

After I got the lumber home, unloaded and the old rotting deck completely removed I could see that the metal frame was suffering from metal oxidation, rust, where the wood had been sitting on the metal and holding moisture. There was also the matter of the very rusted self-tapping lag screws that had held the deck in place and were now were sticking up out of the metal frames cross members. I thought the lag screws were going to be bolts with nuts and washers and I’d be able to remove them, but no, they were not removable. Using a three pound sledge hammer, I broke the lag screws off at the metal cross member and using my angle grinder I ground the little broken nubs of the lags off smooth. For the next hour, using the grinder and my drill with a wire brush wheel, I remove as much rust as I could. After I felt like I had most or all of the loose rust removed I washed the trailer with soap and water and rinsed it with the hose garden hose. Using my leaf blower, I blew most of the water off the trailer and let it sit in the sun to dry, while I went in the house to put on my painting clothes and drink a bunch of water. Did I mention that it was ninety degrees outside?

Lately I have been using Rustoleum 2X paint on my motorcycle projects and so far I have been impressed. 2X is a paint and primer all in one and of course it also fights rust. I had picked up a quart of black 2X and a cheap paint bush when I bought the lumber. When I opened the can I thought, “great, they put dark blue paint in the can and put gloss black on the label”. But, I thought, “what the heck, I’ll have a dark blue trailer instead of a black trailer” and started painting. Well as it turns out the paint is magical. It went on blue, but turned black as it dried. I applied the paint liberally onto the areas that the wood deck would sit on and in and when I was done painting, I pushed the trailer into my shop to let it dry overnight.

DSCF7204

This morning I got early, while it was still cool, to put the wood deck on. In case you didn’t know this, on most trailers, both ends of the wood decking are held in place by metal channels. It’s a good design, but makes replacing the wood deck challenging. To replace the decking you have to place one end of the plank into one of the channels, angle the plank across the trailer, slip the other end of the plank into the channel at the other end and using a hammer and block of wood, drive it in place, parallel to the side of the trailer. It sound easy, but the channels were rough from years of rust and that corrosion made the diving the planks difficult. To add difficulty to the situation, there is a 2”wide metal plate that runs along both sides of the trailer, front to back. Instead of welding the plate flush to the bottom of the channels at the front and back of the trailer, they laid the plate in the channels and welded it in place. This makes the joint stronger but it also creates a lip in the channel that makes it difficult to slide the two side planks in place because the edge of the plank and the edge of the welded plate conflict.

Showing where the side plate is welded inside the channel

Showing the side plate welded inside the back channel.

To combat the roughness of the inside of the channel and the lip the plate and weld created I used axle grease to coat the inside of the channel. The grease not only allowed the planks to slide in the channel easily, it will also acts as an additional preservative to the inside of the metal channel and the ends of the planks where they sit in the channel and where moisture is most likely to be held.

DSCF7209

Showing me greasing the inside of the back channel.

In addition, to make it easier for the edge of the plank to slide over the edge of the plate and weld, I rounded the edge of the plank by tapping on the square edge of the plank with my hammer. With the grease in place in the channels and the edge of the plank slightly rounded, the plank drove easily into place.

 

 

DSCF7219

Showing how to round the edge of the board so it will easily slip over the weld and side plate.

Lying the planks at an angle, slipping both ends into the channels and driving them into place only works with the first six planks. After the first six are angle into place there isn’t enough space to angle any more planks and get both ends started. That is when it starts to get fun.

DSCF7221

Showing how planks can be laid at an angle to get them started into the channels.

To get the rest of the planks to insert into the channels at the front and back of the trailer you now have to bend or bow the middle of the planks up. This shortens the length of the plank and allows you to insert both ends of the plank into the channels. There are probably several methods of doing this and you can probably do this with one person, but two people make it so much easier. This how my wife and I accomplished this next step; First you insert one end of the plank into the back channel, then using a floor jack and a 12” piece of scrap 2X4 or 4X4, one person jacks the center of the plank up while the other person pushes the front end of the plank down. When the center of the plank bows high enough the plank will become short enough that the front will be lined up with the opening of the channel. While the end of the plank is held lined up to the channel the other person lowers the jack and the end of the plank will slip into the channel. The last plank fit so tightly that I had to grease the side of the plank so it would slip down into place. The whole process of decking the trailer when fairly quickly, even with my wife helping, I meant, with wife helping. Thanks Honey!

DSCF7224

Showing the jack in place and ready to bow the center of the plank up in the middle.

DSCF7223

Some other things to consider:

  1. When choosing the boards for the deck makes sure they are straight and without big knots. You don’t want to have to fight warped boards into place and when bowing the boards, large knots can cause a weak point in a board and the board may break or crack.
  2. Buy boards without cracks. Pressure treated wood is only treated into the board .44 of an inch. Cracks that go deeper will allow water into the board and the board will rot from the center out.
  3. Buy boards that are still high in moisture content. Moist boards will be easier to bend and there will be less chance that they will break.
  4. If and/or when you drill holes through the boards and frame for bolts to hold the boards in place, treat the holes with a good dose of oil or wood preservative. This will help keep the wood from rotting around the bolts.
  5. Consider not drilling bolt holes through the boards. The boards fit tightly and will not fall out of the channels even if they shrink slightly. I am going to wait and see how loose the boards get when they dry. If I need to add bolts to hold the deck boards in place I will first explore the possibility of placing the bolts between the deck boards. If a lag bolt that will slip between each the boards, a large washer at the head should hold the deck boards secure to the frame and you can avoid drilling holes in the board.

Anyway…for what it’s worth.

The Transformer Motorcycle

Standard

DSCF7198

 

When I bought this 1981 Suzuki GS850 I was tempted to just polish it up, get it running well and sell. Most of the time though, I can’t leave well enough alone. After considerable contemplating I decided to make the bike a “Transformer.” Transforming from the stock bike to a bobber.

Bobber motorcycles are very popular, but to me, Bobbers are limiting. They’re cool, but limiting when it comes to riding for miles and many hours. What I wanted to do is create a bike that could go from stock to bobber with a bunch of variations in between and back to stock. When you buy a bike you pretty much get what you bought, cruiser, dual sport, café racer, bobber, crotch rocket…, but why not have a bike that can be changed to fit your need or mood.

When bike makers see this blog I’m sure they all will rush to make a Transformer bike.

GE DIGITAL CAMERA

 

Here is what I did to make the bike into the Transformer; First I wanted to make a bobber style seat that would offer some comfort and would easily be installed and removed using the bike’s current brackets. This modification was perhaps the most time consuming. Bobber seats are pretty minimal, but I wanted something that would offer some comfort and yet look minimal. I’ve seen bobber seats that were metal farm tractor seats and though they look cool, I don’t think you’d want to ride all day on one.

I chose to make the seat out of plastic from a plastic barrel. I did this for two reasons; One, I like working with plastic barrels and second, I felt that plastic would offer some flex when sitting on it for long periods. To get the style I wanted, I cut the seat from the bottom of the barrel, leaving a couple of inches of the side of the barrel attached at the back of the seal. This would give the seat a raised back edge so it would look like just a flat board seat and the back raised edge would give the seat some flex. I covered the seat with first a layer of firm rubber yoga mat, then 1.5 inches of memory foam and covered it with black leather looking vinyl. The final product looks pretty good and is pretty butt form fitting.

DSCF6995

DSCF7024

 

 

 

 

 

 

The original seat clips under two brackets at the front by the tank and lockded into another bracket at the back over the back fender. I wanted to use those same brackets for the new seat so I made a base for the seat, out of plastic.This gave me a base of attach the seat to.

DSCF6986

DSCF6999

To attach the new seat to the bike I wanted to make it attach just like the original seat. At the front of the plastic base I welded together a bracket similar to the one on the original seat and attached it to the front of the plastic base with screws.

DSCF6998

The back latch was a little more complicated, but simple in nature. I made a slot in the seat base that would slip over the back metal bracket on the bike. So the plastic base would be secured down, I made a spring loaded latch, out of more plastic, a spring and small screw driver that I removed the handle from and bent the end so it would be easy to grab. This picture shows the base clipped to the bike’s bracket with the spring loaded screw driver. The other piece of plastic is the top piece, shown upside down, that holds the spring and screw driver in place.

  DSCF7022

To install the seat base on the bike you simply slip the front into the front bracket, pull back the spring loaded latch, slip the slotted base onto the back bracket, release the spring loaded screw driver and lock it in place. The seat is bolted to the base using two small bolts. To make sure the seat unit doesn’t flex too far down, I installed a 2” x 8” plastic pipe across the frame of the bike under the seat. The pipe keeps the seat off the battery and wiring and adds to the flexing and comfort of the seat.

With the new seat on, the bike was starting to take on a bobber appearance, but I felt like if the back was lowered a little it would look better. Some bobber builders remove the back shocks and replace them with metal pipes that are shorter than the shocks. This lowers the bike, but offers no suspension. They call this a “Hard-tail,” because it’s hard, no suspension. I call it a “butt buster” or “back breaker.” I wanted to keep the shocks so the bike could be ridden with more comfort. If you’ve read any of my past motorcycle blogs you know I’m all about a comfortable ride.

The tops of the springs are attached to a threaded post, one on each side of the back fender, that are welded to the bike’s frame. The shocks slip onto the posts and are secured with a nut. To lower the back and keep the shocks I added two more threaded posts, one on each side, but I moved them up on the frame 1.5” and back slightly. To add the new posts I drilled a hole through the bike’s tubular frame, one on each side. I bought two bolts that would fit through the tops of the springs, cut the heads off the bolts and slipped them through the holes. I then welded the bolts in place on both sides of the tubular frame. Because the shocks are still installed the bike is called a “Soft-tail.” I call it “Heavenly.”

With the new bobber style seat and with the back lowered, the bike looked a little more bobberish, but not bobbered enough. Most bobbers have a raised gas tank. Some even have very small tanks that are almost head height. I decided the bike would look more “bobber” if the tank was raised up at the front. To accomplish this I again wanted to keep the original tank and attachment brackets. The front of the tank attaches to the bike with two slotted brackets on the under side of the tank that slip onto two “ears” attached to the bikes tubular frame. I raise the front of the tank by duplicating the two ears and welded them to a bracket that would straddle the bike’s tubular frame and slip onto the original “ears.” That worked and raises the front of the tank 2”.

DSCF7072

The signal lights on the bike are very large and kind of ugly. The lights, one on each side of the front and one on each side of the back, are attached to the bike on short tubes that stick out from the bike. I thought about replacing them with smaller L.E.D. lights, but I’ve ridden with guys that have converted to smaller lights and I find them hard to see. It’s my opinion that when riding a motorcycle you don’t want any light on the bike that is hard to see. I scratched my head for a while and decided to keep the signal light, but droop them by cutting the base of the of the tubes, where they attach to the bike, at an angle so the lights sloped slightly down giving them a drooped look.

DSCF7141

The stock tail light is huge. The light itself is large and square and the metal base that the light is attached to is kind of massive and not in keeping with the bobber simple look. I decided that when the bike is transformed into the bobber style, a round tail light with a small bracket would look better. You can buy many different sizes from your local automotive store. I chose one that I thought would be easy to see and look right for a bobber. (The white towel is to hide the license plate for whatever reason people do that.)

The handlebars that came with the bike may not have been stock. They were the style that raise up and swoop back and down. They were kind of funky looking and hurt my wrists after about five minutes of riding. I prefer something shorter and wider with only a sight pull back. The bars seemed useless to me so I cut them up and welded them back together in a more suitable style for my purpose. The result was handlebars that are more comfortable and better looking.

The thing about the bobber style is that most bobbers make you sit on a lowered bike with a flat seat and with the original foot shifter and brake in the original places. If you are taller, like me, this puts your knees in a very bent position. When I was younger that knee bent position wouldn’t have bothered me as much. Now that I’m older, lets say 40ish, bending my knees at such a squatted position is a deal killer. And knee killer. To remedy this uncomfortable riding position I made a forward shifter and forward brake mechanisms called forward controls. I wanted to keep the original shifter and foot brake lever in tact, so that the bike could be converted back to the original style. I did some shopping on Ebay and found replacements for a very reasonable price, like $36. for both with free shipping. I took the Ebay levers and cut them in-two, made brackets that attach to the frame in front of the motor, added pegs, rods, more brackets, etc… and I had forward controls that allowed me to stretch my legs forward, making the ride more comfortable.

DSCF7068

With all these modifications the bike can be set up in about 36 different configurations. You can change the seat or not, keep the front fender, or not, change the break light, or not, use forward controls, or not… raise the tank, or not, lower the back, or not, well you get the idea.

The last step was to paint the bike. A lot of people like “blacked out” bikes. I like them, but I wanted to add some bright highlights. I chose orange to give the bike some snap, some pop, some eye catchiness. To black out the bike, I cleaned the motor and sprayed it and the exhaust with a heat resistant paint. The rest of bike I painted first with black spray on truck bed coating, added the orange highlights and then clear coated it. I’m sure everyone will have their own opinion about how the bike looks, but I’m pleased with the results.

DSCF7202

DSCF7201DSCF7199

This bike is my second winter project this year. The idea was to buy it, fix it, sell it and make a little cash. With this bike I made so many modifications that I told my wife that “I should hold onto it for a few months and ride it to make sure all the bugs are worked out and that it’s running right,” And that’s true, but this bike is a kick in the pants to ride and that’s true too.

There is a lot of parts to this project and each part could have been a blog in it’s self. If you decide to attempt any of these customization and need more information, please feel free to email me or leave your questions in the comments.

Anyway… for what it’s worth.

 

 

 

 

 

 

Highway Pegs for Adventure Bikes

Standard

DSCF7127

One of the best additions I’ve made to my V-strom is the highway or forward pegs. Having the option of stretching my legs forward and resting them on foot pegs is a real relief when I’ve been riding for hours. Making the forward pegs is also one of the more difficult additions I’ve made. In all honesty I have to admit that the project of making the pegs was made difficult by the fact that I am a cheap bastard and instead of buying square metal tubing I used what I had, round pipe. To make the forward pegs for an “Adventure Bike,” I had to make them hinged so that they would fold up and out of the way in rough riding conditions and so they could easily fold back down when riding on the highways. To make them hinge with round pipe I had to heat the ends of the pipe until it was red hot and then hammer the round pipe into perfectly square ends. It gets even more complicated and difficult when one of the… well never mind, let me just tell you how to do this the easy way.

First you have to have a skid plate on your bike. For my V-strom I bought a skid plate. I had all kinds of ideas of how to make a skid plate, but I got such a great deal on the bike that I convinced myself that I could afford to buy the plate. Without a skid plate you might be able to attach to your crash bars, but you’ll have to buy crash bars. The forward pegs are three separate pieces, a long bar that bolts across the front of the skid plate and two shorter bars that are the foot pegs. The two foot pegs attach to the long bar at both ends with a single bolt that acts as your hinge pin. For my bike the long bar is 16” and the foot pegs are 6.5”. I’ve been pretty happy with those lengths, but you may want to make adjustments for your particular bike or riding style.

To make them out of square tubing you would cut the long bar at 16″, but leave a bottom tongue on both ends sticking out about 1″. The pegs are 6.5″ with the bottom corner rounded so it will hinge up and not drag the bottom corner. Cut four 2″ ears out of flat stock and weld them to the ends of the main bar with 1″ of the ears sticking out past the main bar. The ears will be welded to the tongue and main bar, one on each side. The other option is to buy foot pegs and bolt them to the main bar, but what fun would that be?

DSCF7136DSCF7138

I bolted my long bar to my skid plate with two “U” bolts. To make the foot pegs less slippery and to dress up the pegs I used a pair of rubber handlebar grips and slid them onto the pegs. They worked pretty well, but I failed to glue them on and they had a tendency to slid outward. On a trip to Glacier I lost one outside White Salmon, so I went into a hardware store found a heavy duty black rubber hose that would slide tightly onto the pegs and I’ve use that since. In my shop I found a couple of plastic caps off some kind of aerosal spray cans, probably brake cleaner, to cap the ends of the rubber hose to make the ends of the pegs look a little more finished.

DSCF7137

Like I said, one of the best addition I’ve make to my V-strom. I’m not young, have a little arthritis in both knees and being able to stretch out my legs is so nice.

IMAG0061

Anyway…for what it’s worth.

Indestructable Tomato Cages

Standard

DSCF7102

So anyway, I think my wife might be insane. Here’s why; every year she plants tomatoes and every year she buys the cheap flimsy tomato cages for the plants to grow on and every year the plants grow up on the cages and tip them over, bending them to the ground. I believe the definition of insanity is -“Insanity: doing the same thing over and over again and expecting different results.” I still love her.

Last year as the tomato plants and tomatoes lay on the ground I told her I would make her tomato cages next year. Hey, I had to do something to stop the insanity. So next year is here and I made her tomato cages.

My youngest daughter and son-in-law have three sons. Myles is the middle son. My mom had three sons. I was the middle child. It’s interesting to watch Myles struggle to find his place in the family. I can relate to the struggle because I also struggled to find my place in my family. As a middle child you really do get ignored, especially if your older brother is cool and your baby brother is cute. His are. Mine were. His mom tries very hard to make Myles feel special, but when his friends come over to play they are drawn to the coolness of his older brother, the cuteness of his baby brother and Myles is mostly left out. Myles is good at passing time playing alone with his toys and is best friend, “imagination.” My mother claims that I did the same.

Myles just had a birthday and for his birthday he wanted tomato plants so he could grow his own tomatoes. He loves tomatoes. When my wife, his Nana, heard this, she decided “we” should make a raised garden and surprise him with the garden and tomato plants. He’s four.

I know it is a little odd a four year old wanting tomato plants for his birthday, but again, I can relate to that oddness. Ask anyone to describe me and they will use many different adjectives and “odd” will always be one of those adjectives. Most people will use restraint and not say it out loud, but the adjective “odd” will be top of mind and on the tip of their tongues. (“Odd”-Deviating from what is ordinary, usual, or expected; strange or peculiar.)

So I built Myles a raised garden out of 1″X6″ cedar. The garden is 2’X6’ and 11” tall or deep. 2″X6″ cedar would last a lot longer, but 1″X6″ will probably out last his interest in growing tomatoes.

I also routered out a sign that says “Myles’ Garden – Love Nana and Grandpa.” I didn’t have room to say, “Love Nana and Mr. Grandpa Larson,” which is what I insist that all my grand kids call me, so the sign just says Grandpa.

Long story short, I also made Myles tomato cages.

I made the cages out of 3/8” rebar. I figured that 3/8” would be strong , last a long time and the lumber yard was all out of ¼”. Our local lumber yard, Stayton Builders Mart, stock not only rebar, but they also have a rebar cutter. I figured that out of a 20’ piece of rebar I could cut five, 4’ piece out of the bar. Tough math. My plan was to make the cages 4’ tall, with four sides and each side would be 1’ wide, 4’X1’=4′. I bought enough rebar to make six tomato cages. Myles only needed two and my wife needs three, but she told me to make her four because someday she would retire and grow four tomato plants. Clearly she has her retirement activity all planned out, pushing her limit to four plants.

So the Builder’s Mart sold me the rebar, pointed to the cutter and said, “knock yourself out.” The chore of cutting went pretty quickly after I set up a cutting guide. I positioned the cutter 4′ from the base of the lumber rack, slide the rebar end against the rack and cut. Once I had all 45 of the 4′ pieces cut, I took them home, laid them all out in a nice flat row and using water and a wire brush I tried to remove as much rust and crud as I could

.DSCF7085

I let the bars dry and then painted them red. My wife wanted them painted red so that it would look like we had tomatoes before the tomatoes actually tuned red. What can I say, she is, after all, insane.

DSCF7086

After the paint dried I marked twenty four of the bright red 4′ bars into 12″ increments. Then I clamped each bar in my bench vice and bent them into 1′ squares using a piece of pipe that I slipped over the bars for leverage. It wasn’t as much fun as it sounds and welding the squares onto the 4′ legs was even less fun. After several frustrating hours trying to hold the legs and squares together while welding them I got all six cages welded together. After I finished welding each cage, I tested my welds by tossing the completed cage out my shop door onto the gravel driveway. It wasn’t much of a test, but it made me feel better. Of course, after bending and welding the cages I had to touch up the paint.

DSCF7099

In the end, the cages turned out pretty well. Am I glad I spent all that time making indestructible tomato cages? Yes. Would I do It again? Probably, but I am a glutton for punishment. If you take on this project, get a friend to help you hold the parts together while you weld.

Anyway…for what it’s worth.

 

Getting Organized and Clear Your Head

Standard

My boys once called me the “Master Rattle Canner.” I do love rattle cans and have painted many things, transforming them from junk to a jewel. The good thing is that the fumes from the paint have not affected my BrA1n N0n3. Over the years my wife, my boys and I have bought hundreds of cans of spray paint for projects we have done. When I moved my stuff from our garage to our new shop we had accumulated over seventy cans of practically used spray paint. To move them to the shop, we put all the cans in two large plastic containers, moved them to the shop and in those two containers they stayed for a year and a half. The problem with having that many cans of paint is that you have to be able to organize them so that you know what you have and so you don’t keep buying more of the same colors over and over again. When I moved into the shop I wanted to organize it so that everything had a place. I put up pegboard, built a bunch of shelves, bought small boxes to organize stuff in, but the two plastic containers of spray paint had me stumped on how to organize them.

DSCF6951

The other day I was shopping at Goodwill, which used to be my favorite store until they raised their prices higher than regular retail, but I still shop there in hopes that I’ll find a bargain. So I was in Goodwill and found a metal rack for displaying wine in a store and I thought, “hey!”  The rack was marked $6.99 and would hold forty bottles of wine/cans of spray paint and with some minor alterations, it would hold sixty cans.

DSCF6953DSCF6954

Today I started going through the two containers of spay paint, properly disposing of six cans that were empty and cleaning the heads of the other cans that still had paint, but wouldn’t spray.

Over the years I have learned that when you are done painting something, if you really do turn the can upside down and spray until the spray is clear, the spray head will be cleaned and will work the next time you want to use the can. I now will even go as far as spraying the little spray hole with carb or brake cleaner and wiping it off with a cloth just as an extra precaution. With that said, I don’t always remember to do clear the head and it gets clogged with paint and won’t work. I hate that, having a paint can with paint in it, but won’t spray because the head is plugged with dried paint.

Out of the two containers of spray paint there were about fifteen cans that had paint in them, but would not spray, so I cleaned the heads. This is my method of cleaning a spray can head: I use brake or carb cleaner, a straight pin that is exact size or smaller to insert into the little hole the paint sprays out of, a utility knife, safety glasses and latex gloves.

First remove the head from the can by simply pulling it out of the can and spray a little carb or brake cleaner into the hole in the top of the can where the head was and let that sit while you clean the head.DSCF6949 Next, using the utility knife, scrape off any paint that has dried over the little hole.

DSCF6948

Sometimes that’s all it takes to clean the head, so test the head to see if it is clear by inserting the thin red tube that comes with every can of brake or carb cleaner up the neck of the of the head and being careful to point it away from my face, spray the cleaner into the neck.

CAUTION: You will need to secure the head on the tube by pinching it tightly with your fingers where the tube goes into the neck or you will shoot the head across the room and/or you will get cleaner on your face.

DSCF6945

If the cleaner sprays out the head’s small hole, it’s clean. If it’s plugged, take the pin and carefully push it into the small spray hole and up the neck to clear the plug.

DSCF6947

To make sure the head is clear, spray some cleaner in the neck again. Some plugs can be stubborn and you’ll have to repeat the process a couple of times, but this method will unplug the head. When the head is clear, point the head away from you, push it back in the top hole of the can, turn it upside down and check the spray. This cleaning method worked on all but two of the fifteen cans that I had that were clogged. As an extra precaution, I sprayed the head with cleaner and wipe the small hole with a cloth. Next time you want to use the spray paint it will be ready to use.

When you use the can of spray paint up, remove the head, clean it and save it. There have been many times I have dropped a can or knocked it off the bench, losing or breaking the head. Having a few extra heads around will allow you to still use the can of paint until it is empty.

Anyway…, for what it’s worth.